1. |
Index to Advertisers in this Issue |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 93-95
Preview
|
PDF (301KB)
|
|
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00193.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
2. |
Accurate measurement of residual stress on any steel using the centre hole method |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 99-106
E. M. BEANEY,
Preview
|
PDF (861KB)
|
|
摘要:
The centre hole method has been shown to be a simple and reasonably accurate method of measuring residual stress. With a 1.6 mm diameter hole, the method can be applied on operational plant and the equipment required is sufficiently portable for use on site. Its application has, however, been limited to use on low‐strength steels, due to problems associated with forming the hole.This paper describes the development of an air‐abrasive technique for forming the hole, which allows the centre hole method to be used on any steel with a measurement accuracy of better than
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00194.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
3. |
A simple triaxial rig for studying the creep of concrete at elevated temperatures |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 107-112
A. LUXMOORE,
S. SEKISAMBU,
Preview
|
PDF (837KB)
|
|
摘要:
The design and testing of an apparatus for studying the creep of concrete at temperatures up to 200°C, under triaxial stress conditions, are described. Initial test results confirm that the apparatus is satisfactor
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00195.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
4. |
Measurement of bearing reactions in small‐scale bridge slabs |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 113-119
A. S. TOOTH,
A. COULL,
I. P. PERCY,
Preview
|
PDF (864KB)
|
|
摘要:
An experimental technique is described for the measurement of bearing reactions in small‐scale bridge slabs. The reactions are determined implicitly by direct measurement of the frictional forces between the slab and its supporting abutment, using thin pull‐out steel st
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00196.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
5. |
Misuse of regression techniques in calibration |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 120-121
J. D. SMITH,
Preview
|
PDF (175KB)
|
|
摘要:
The use of standard computer regression techniques in the calibration of transducers leads to incorrect deductions when hysteresis is present. The ‘best’ line obtained does not minimise errors and valid points may be rejected whilst invalid experimental points are retained. An alternative graphical technique is suggested and the problems associated with the zero point are discus
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00197.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
6. |
Society News |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 123-123
Preview
|
PDF (112KB)
|
|
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00198.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
7. |
Book Reviews |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 124-124
Preview
|
PDF (123KB)
|
|
摘要:
Book reviewed in this article:A Background to Engineering Design by Peter Polak,Stress Analysis by the Finite Element Method for Practicing Engineers by W. H. Bowes and L. T. Russell
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00199.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
8. |
Industrial and Research News |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 127-130
Preview
|
PDF (563KB)
|
|
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00200.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|
9. |
new products |
|
Strain,
Volume 12,
Issue 3,
1976,
Page 130-132
Preview
|
PDF (340KB)
|
|
ISSN:0039-2103
DOI:10.1111/j.1475-1305.1976.tb00201.x
出版商:Blackwell Publishing Ltd
年代:1976
数据来源: WILEY
|