|
1. |
The Effects of Processing on the Photooxidation of Polymers |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page 1-25
Gerald Scott,
Preview
|
PDF (797KB)
|
|
摘要:
The photooxidation of polymers is of considerable practical significance since the rate of this process controls the useful service life of most polymers in outdoor applications. Low-density polyethylene in the form of film remains essentially unchanged for many years when stored at ambient temperatures indoors in the absence of direct sunlight. Out-of-doors, by contrast, even when stabilized with the most effective commercial UV stabilizers at present
ISSN:0360-2559
DOI:10.1080/03602557808067653
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
2. |
A Review of The Significant Developments in Glass Fiber Reinforced Thermoplastics: 1966-1975 |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page 27-39
JohnE. Theberge,
CharlesV. Goebel,
Preview
|
PDF (323KB)
|
|
摘要:
This review addresses itself only to the significant glass fiber reinforced thermoplastic developments (GRTP's) during the period 1966–1975.
ISSN:0360-2559
DOI:10.1080/03602557808067654
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
3. |
Fluorocarbon Elastomers: A Technical Review |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page 41-53
J.D. Maclachlan,
Preview
|
PDF (473KB)
|
|
摘要:
Fluorocarbon elastomers were first introduced in the mid-1950s. During the past 20 years they have found wide use in a variety of applications and have established themselves as an important class of elastomers. Their success and continued growth as high performance materials is a result of their unique balance of physical properties. As a class, they are superior to most other types of elastomers in resistance to degradation at elevated temperatures and resistance to swelling in a wide variety of fluids. This superiority is evident in the ASTM D-2000 classification system where fluorocarbon elastomers normally carry the designation HK for type and class. This system specifies that fluorocarbon elastomers shall be tested for 70 hr at 482°F for resistance to degradation in hot air (the H term) and for 70 hr at 302° F (maximum allowable temperature for the fluid) in ASTM No. 3 oil for fluids resistance (the K term). Under these conditions, heat aged properties must not change more than that indicated in Table 1 while volume increase in the specified oil must not exceed 10%. These test requirements are the most severe of any elastomer described in this ASTM classification system.
ISSN:0360-2559
DOI:10.1080/03602557808067655
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
4. |
Weatherable Impact-Modified Rigid PVC |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page 55-80
JohnT. Lutz,
Preview
|
PDF (624KB)
|
|
摘要:
Polyvinyl chloride (PVC) is the most adaptable synthetic polymer. Starting with the base polymer that is heat and UV light sensitive and relatively brittle, compounders can produce articles ranging from soft (“soggy”) fishing lures to hard, rigid, high impact building materials. This tremendously wide spectrum of products is made possible through the addition of stabilizers, lubricants, plasticizers, and polymeric modifiers.
ISSN:0360-2559
DOI:10.1080/03602557808067656
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
5. |
Recent Advances in Organotin Polymers |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page 81-116
R.V. Subramanian,
B.K. Garg,
Preview
|
PDF (1721KB)
|
|
摘要:
The science and technology of organotin polymers are based on the properties of organotin compounds which have surprisingly diverse applications, including use as stabilizers for vinyl chloride and other olefm polymers, as industrial catalysts, as industrial and agricultural biocides, and as antifouling and wood-preserving agents. In keeping with the expanding use of organotin compounds, the worldwide production of organotin compounds has risen dramatically from less than 50 tons/yr in 1950 to over 25,000 tonslyr in 1975 [1]. The chemis-try of organotin compounds, including the preparative methods, properties, chemical reactions, and uses, has been reviewed in several recent monographs and symposia proceedings [1–5]
ISSN:0360-2559
DOI:10.1080/03602557808067657
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
6. |
Editorial board page for “Polymer-Plastics Technology and Engineering”, Volume 11, Number 1 |
|
Polymer-Plastics Technology and Engineering,
Volume 11,
Issue 1,
1978,
Page -
Preview
|
PDF (31KB)
|
|
摘要:
This is a scanned image of the original Editorial Board page(s) for this issue.
ISSN:0360-2559
DOI:10.1080/03602557808067652
出版商:Taylor & Francis Group
年代:1978
数据来源: Taylor
|
|