1. |
The Effect of Inspector Accuracy on the Type I and Type II Errors of Common Sampling Techniques |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 157-164
HoagLaverne L.,
FooteBobbie L.,
MountClark,
Preview
|
PDF (899KB)
|
|
摘要:
The single sample and sequential sampling models are presented in a form which includes inspector error. The effect of inspector errors on the probability of type I and type II errors is discussed.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980691
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
2. |
A Simplification of Skip-Lot Procedure Formulation |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 165-167
BruggerRichard M.,
Preview
|
PDF (366KB)
|
|
摘要:
The ordinary method of describing such properties as the operating characteristic curve of a skip-lot procedure can be difficult and time consuming. A method is provided which lessens this effort considerably.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980692
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
3. |
Simulation: An Application to Quality Control |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 168-172
CousinsW. T.,
FrederiksenJ.,
NarulaSubhash C.,
Preview
|
PDF (451KB)
|
|
摘要:
When it is difficult or not possible to solve a problem analytically and not feasible to carry out a designed experiment on the production floor due to the interference it causes in day-to-day operation, simulation provides a viable alternative. This paper discusses the use of simulation as a management tool in decision making, in particular to determine specification limits.A simulation flow chart of an assembly process is presented along with the results of its application to actual operation.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980693
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
4. |
Maximum Allowable Percent Defective (MAPD) Single Sampling Inspection by Attributes Plan |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 173-182
SoundararajanV.,
Preview
|
PDF (958KB)
|
|
摘要:
In this paper, Single Sampling Attributes Plans indexed by Maximum Allowable Percent Defectives (MAPD) are given. A table, for transition from one set of parameters to match the Operating Characteristic Curve (OC curve) to other similar sets, is given.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980694
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
5. |
Recent Developments in Control Chart Techniques |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 183-192
GibraIsaac N.,
Preview
|
PDF (1664KB)
|
|
摘要:
In the last three decades several control chart procedures were developed. Prominent among these, are the Cumulative Sum, Economic design of X̄-control charts, Acceptance and Multi-characteristic charts. This article presents description and analysis of these charts in an attempt to bring past research into current perspective.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980695
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
6. |
Traceability? |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 193-195
CameronJoseph M.,
Preview
|
PDF (441KB)
|
|
摘要:
The requirement of traceability of instruments to nationally accepted standards or measurement systems has as its goal the adequate accuracy of measurement, the compatibility of different measurement systems, the interchangeability of parts, etc. This note discusses a perspective in which these goals are approached directly by performance requirements on the quality of measurement rather than a property of an instrument, namely traceability.
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980696
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
7. |
A Runs Test for Sample Non-Randomness |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 196-199
RaoufA.,
SathéP. T.,
Preview
|
PDF (474KB)
|
|
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980697
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
8. |
A Nomograph of Student's t |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 200-201
NelsonLloyd S.,
Preview
|
PDF (164KB)
|
|
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980698
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
9. |
Multivariate Statistical Methods for Business and Economics |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 202-203
McHenryC. E.,
Preview
|
PDF (341KB)
|
|
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980699
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|
10. |
Economic Decision Analysis |
|
Journal of Quality Technology,
Volume 7,
Issue 4,
1975,
Page 203-204
ThatchDaymon W.,
Preview
|
PDF (296KB)
|
|
ISSN:0022-4065
DOI:10.1080/00224065.1975.11980700
出版商:Taylor&Francis
年代:1975
数据来源: Taylor
|