1. |
Institute of Ferrous Metallurgy of the Technical University, RWTH, Aachen – IEHK |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 299-305
Preview
|
PDF (1039KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198600768
出版商:Wiley
年代:2016
数据来源: WILEY
|
2. |
Hematite ore reduction to magnetite with CO/CO2– kinetics and microstructure |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 306-311
Mohamed Ettabirou,
Bernard Dupré,
Charles Gleitzer,
Preview
|
PDF (617KB)
|
|
摘要:
Uncertainties and discrepancies are common in the first step of the reduction of hematite ore to magnetite, especially as regards the experimental conditions governing the transition from porous to lamellar magnetite. Hence the problem has been reinvestigated with an ore from Itabira (Brazil).This ore has been carefully characterized with X‐ray diffraction, X‐ray photoelectron spectroscopy, optical and scanning electron microscopy and electron microprobe analysis. It has been established that α‐quartz and goethite are present, and iron combined on the surface with S or Si; most particles, in the range 50–200 μm, are hematite single crystals with 0.1% Al as the only substitution; there are also smaller crystals agglomerated by the gangue.Numerous experiments have shown that the transition from porous to dense lamellar magnetite is enhanced by an increase of temperature and a decrease of CO %. This is explained by a competition between the chemical reaction and solid state diffusion of ions along the hematite‐magnetite interface.The shrinking‐core model has been applied to the domain of porous magnetite, yielding a chemical rate constant ϕ = 15.5 exp (−69500/RT), roughly twice lower than in the reduction of hematite synthetic single crystals. The nucleation frequency increases sharply with temperature to ∼700°C where it reaches ∼109m−2·s−1, as with pure hematite.
ISSN:0003-8962
DOI:10.1002/srin.198600769
出版商:Wiley
年代:2016
数据来源: WILEY
|
3. |
Metallurgische Wirkungsweise, zweckmäßige Frequenz und Polpaarzahl der azimutalen Rührer im Kokillenbereich |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 312-317
Franz‐Rudolf Block,
Edmund Julius,
Preview
|
PDF (552KB)
|
|
摘要:
Von einem Überblick über die metallurgische Wirkungsweise ausgehend, werden für verschiedene Frequenzen und Polpaarzahlen die beim elektromagnetischen Rühren mit Drehfeldern in der Schmelze induzierten Kraftdichten und Verlustleistungen unter Einbeziehung der Abschirmwirkung der Kokille und der Rückwirkung der rotierenden leitenden Schmelze berechnet. Über 90% der vom Rührmotor aufgebrachten Leistung werden in der Kokille in Wärme umgewandelt. Bei gleichem Strombelag weist die Kraftdichte als Funktion der Frequenz ein Maximum auf. Doch ändert sich in diesem Frequenzbereich die Kraftdichte deutlich mit der Rotation der Schmelze. Die zweckmäßige Wahl von Frequenz und Polpaarzahl wird erörtert.
ISSN:0003-8962
DOI:10.1002/srin.198600770
出版商:Wiley
年代:2016
数据来源: WILEY
|
4. |
ECSC announcements |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 317-317
Preview
|
PDF (105KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198600771
出版商:Wiley
年代:2016
数据来源: WILEY
|
5. |
An error analysis for visioplasticity data processing |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 318-324
Hans Joachim Pehle,
Reiner Kopp,
Preview
|
PDF (1057KB)
|
|
摘要:
The conducted investigations are concerned with the effect of data errors on the calculations of stress and strain components according to the visioplasticity method. The error analysis was based on an evaluating process suitable both experimentally and theoretically for exact calculations. Longitudinal sectional areas of rod drawing stock were marked photochemically with measuring grids with a line spacing of 0.1–1 mm. Specimens thus prepared were partially drawn and the deformation patterns were registered by means of a measuring microscope.The measured data were evaluated with the aid of a smoothing and calculating procedure based on cubic spline approximations. This procedure was checked with a flow model and proved to be suitable for exact visioplasticity calculations. Error investigations were carried out in order to examine the influence of a measured data scatter on the visioplasticity calculation results and an error size was defined and used to establish an error curve according to three different methods. By means of this function it is possible to quantify – as has been indicated by means of an example – the calculation error for a given quantity of data or, depending on the accuracy and aim of the calculations, the demands on the measuring grid and the data quality can be derived. By the example of the calculation of frictional stresses it has been demonstrated that the spacing of the measuring grid lines must be adjusted to suit the inhomogeneity of the plastic flow. If need be, a special more sophisticated method of evaluation is necessary – as described in5) – to determine accurately such inhomogenous strain patterns.
ISSN:0003-8962
DOI:10.1002/srin.198600772
出版商:Wiley
年代:2016
数据来源: WILEY
|
6. |
An approximate theory for calculation of roll torque during edge rolling of steel slabs |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 325-330
Sven Erik Lundberg,
Preview
|
PDF (492KB)
|
|
摘要:
A roll torque model is derived for edge rolling. An upper bound solution assuming plain strain in the draught‐spread plane is designed and the torque is derived.The torque and power calculated by the model is compared to power measurements in the edging stand of the hot strip mill at Fagersta Stainless AB.Slab shape after rolling is compared to estimated. The agreement between estimated and measured slab shape is very good.The calculated power is in good agreement with measurements for conventional stainless steel grade Fagersta R 350 (SS 2333), while the power is sligthly overestimated for the high alloy stainless steels Fagersta R 429 and R 560. The reason for this is probably the used flow‐stress model.As the torque and power model is in good agreement with measurements it can be included in process control systems for width control.
ISSN:0003-8962
DOI:10.1002/srin.198600773
出版商:Wiley
年代:2016
数据来源: WILEY
|
7. |
ECSC announcements |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 330-330
Preview
|
PDF (87KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198600774
出版商:Wiley
年代:2016
数据来源: WILEY
|
8. |
Beitrag zur Charakterisierung der Karbonitride in mikrolegierten Stählen |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 331-334
Andreas Kern,
Winfried Reif,
Preview
|
PDF (397KB)
|
|
摘要:
Zur genaueren Kennzeichnung von Karbonitriden, die in mikrolegierten Stählen auftreten, kann ein thermodynamisch abgeleitetes Mischungsmodell aus der Literatur zur Bestimmung der Stöchiometrie herangezogen werden. Im Fall von zwei metallischen Mikrolegierungselementen kann das Modell entsprechend erweitert werden, wenn eine starke thermodynamische Ähnlichkeit beider Mikrolegierungselemente vorhanden ist. Hiermit ist eine Beschreibung von vierkomponentigen Verbindungen in Stählen, die z. B. mit Nb und V legiert sind, möglich. Die Wechselwirkung der Karbonitride mit vorhandenen Aluminiumnitriden kann durch Betrachtung einer schrittweisen Aufteilung des Gesamtstickstoffgehaltes für jede erreichte Temperatur bearbeitet werden.Die Berechnung der Karbonitridverbindungen von drei mikrolegierten Stählen, die entweder nur mit Nb bzw. V sowie mit Nb und V legiert sind, zeigt bei Temperaturen oberhalb 900°C einen zunehmenden Austausch des Kohlenstoffs durch Stickstoff mit steigender Temperatur. Im Stahl, der mit Nb und V legiert ist und in dem vierkomponentige Nb,V‐Karbonitride berechnet werden können, führt das gegenüber den reinen Nb‐Karbonitriden zusätzlich vorhandene Vanadium zu einer Stabilisierung des Kohlenstoffgehaltes und – bei tiefen Temperaturen – des Karbonitrids allgemein. Zur weiteren Vereinfachung und eindeutigen Charakterisierung der Karbonitride können alle bei 900°C gebildeten Verbindungen als beständig angesehen werden. Durch sie wird das Kornwachstumsverhalten dreier unterschiedlicher Stähle sehr gut beschrieben, was insbesondere den Ansatz von vierkomponentigen Verbindungen im Stahl mit zwei metallischen Mikrolegierungselementen rechtfertigt.
ISSN:0003-8962
DOI:10.1002/srin.198600775
出版商:Wiley
年代:2016
数据来源: WILEY
|
9. |
Berichtigung |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 334-334
Preview
|
PDF (104KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198600776
出版商:Wiley
年代:2016
数据来源: WILEY
|
10. |
Abrasive wear of anisotropic two‐phase microstructures in Fe—Ni—C steels |
|
Archiv für das Eisenhüttenwesen,
Volume 57,
Issue 7,
2016,
Page 335-339
Ursula Herold‐Schmidt,
Preview
|
PDF (771KB)
|
|
摘要:
Isotropic as well as anisotropic ferrite‐martensite microstructures in a Fe‐8 wt.% Ni‐0.37 wt.% C alloy are produced by various thermo‐mechanical treatments. They are characterized by means of microscopy and quantitative stereology and exposed to abrasive wear in a pin‐test apparatus. The observed directionality of the wear rates is explained considering the differences of the respective wear mechanisms. The optimum wear resistance results from an anisotropic microstructure with elongated martensitic regions arranged perpendicularly to the sliding direction.
ISSN:0003-8962
DOI:10.1002/srin.198600777
出版商:Wiley
年代:2016
数据来源: WILEY
|