1. |
Messung von Phasen im Sinter und die Auswirkung bestimmter Phasen auf den Koksverbrauch im Hochofen |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 389-394
Erhard Beppler,
Bernhard Gerstenberg,
Urban Janhsen,
Preview
|
PDF (511KB)
|
|
摘要:
Mit einem Bildanalysesystem werden die im Sinter mit unterschiedlicher Basizität sich ändernden Phasenanteile gemessen. Die bei höher basischem Sinter vermehrt auftretenden Schwierigkeiten der Differenzierung der Sinterphasen werden auf die Überlappung der Grauwertreflexionsbereiche von Kalkferriten und Magnetit zurückgeführt.In Gleichgewichtsmessungen mit CO/CO2‐Gemischen in einer Thermowaagenanlage konnte gezeigt werden, daß insbesondere der C2F nahezu unabhängig von der Temperatur erst bei einer Gaszusammensetzung von CO2’ = 21 % zu Eisen und CaO umgesetzt wird. Dieses Ergebnis ist um so mehr von Bedeutung, als daß alle Arten der Kalkferrite während ihrer Reduktionsumsetzung diesen Ferrit C2F bilden. Für den Sauerstoffaustausch zwischen absinkendem Möller und aufsteigendem reduzierendem Gas bedeutet die Reduktion der Ferrite C2F, CF und CF2bei 900°C für die den Brennstoffverbrauch bestimmende Wüstitecke eine Verschiebung sowohl in Richtung mehr abzubauenden Sauerstoffes als auch zu höherem Reduktionspotential. Für eine ausgeglichene Wärme‐ und Sauerstoffbilanz im Hochofen bedeutet dies, daß das Reduktionsvermögen des aufsteigenden Gases an der den Brennstoffverbrauch bestimmenden Wüstitecke höher liegen muß. Dies hat zur Folge, daß zunehmende Kalkferritanteile im Sinter zu einem Anstieg des Brennstoffverbrauches führen.
ISSN:0003-8962
DOI:10.1002/srin.198700236
出版商:Wiley
年代:2016
数据来源: WILEY
|
2. |
Morphological changes during reduction of magnetite compacts |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 395-398
Ravindra Kumar Dube,
Brahma Deo,
Preview
|
PDF (548KB)
|
|
摘要:
Magnetite superconcentrate compacts were reduced to wustite and iron at various temperatures (1173‐1423 K) and the morphological changes occurring at various stages of reduction were observed under the scanning electron microscope. It has been demonstrated that considerable pitting and fragmentation occur during solid state reduction of Fe3O4to FeO by solid iron. During the reduction of FeO the iron nuclei formed have a tetrahedral shape. At low reduction temperatures (1173 K) the large number of iron nuclei formed on wustite sinter together forming a dense iron layer. At high temperatures sustained growth of nuclei in the vertical direction leads to a sinuous porosity. Genesis of porosity creation has also been explained in terms of formation of holes, slits, cracks and fragmentation in magnetite and wustite and growth and sintering of iron nuclei.
ISSN:0003-8962
DOI:10.1002/srin.198700237
出版商:Wiley
年代:2016
数据来源: WILEY
|
3. |
Schmelzgleichgewichte im System Fe—C—Ca |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 399-405
Eberhard Schürmann,
Hartmut Jacke,
Preview
|
PDF (677KB)
|
|
摘要:
Das binäre Randsystem Ca—Fe ist gekennzeichnet durch eine ausgeprägte Mischungslücke mit sehr geringen Löslichkeiten der beiden Elemente ineinander, während das System Ca—C durch die hochschmelzende kongruente Verbindung CaC2und eine relativ große Löslichkeit von C im flüssigen Ca charakterisiert wird. Die durch das System Ca—C für Eisenschmelzen hervorgerufene Ca‐ und CaC2‐Sättigungslinie im ternären System Fe—C—Ca läßt sich nach thermodynamischer Auswertung der Versuchsergebnisse mit In γcca‐Werten als Funktion der Kohlenstoffkonzentration und der Temperatur beschreiben. Der Gang des Aktivitätskoeffizienten bewirkt dabei, daß die gelösten Ca‐Gehalte mit steigenden C‐Werten zunächst im Bereich der Ca‐Sättigung bis zur Doppelsättigung mit CaC2ansteigen, anschließend im Bereich der CaC2‐Sättigung wieder abfallen, ein Minimum durchlaufen und zur Doppelsättigung mit C und CaC2hin erneut zunehmen.
ISSN:0003-8962
DOI:10.1002/srin.198700238
出版商:Wiley
年代:2016
数据来源: WILEY
|
4. |
Entsphosphorung von kohlenstoffhaltigen Eisenschmelzen mit Calciumcarbid und Calciumcarbid‐Calciumfluorid‐Schlacken |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 406-413
Eberhard Schürmann,
Hartmut Jacke,
Preview
|
PDF (816KB)
|
|
摘要:
Für die bei einer Entphosphorung von Eisenschmelzen mit CaC2auftretenden Sättigungszustände des Zustandsdiagramms Fe—C—Ca—P wurden in der Eisenecke mit den für Eisenschmelzen interessierenden technischen Gehalten an P und C folgende sättigende Phasen ermittelt zu: Calcium, Calciumcarbid, Calciumphosphid, Calciumcarbophosphid und Graphit. Aufgrund der gefundenen Versuchsergebnisse führen die geringen P‐Gehalte im Bereich der Calcium‐ und der Calciumcarbidsättigung zunächst zu erhöhten Ca‐Werten, ehe im Bereich der Calciumphosphid‐ und Calciumcarbophosphidsättigung die P‐Werte mit steigenden Ca‐Gehalten durch ihre Verknüpfung über das Löslichkeitsprodukt abnehmen. Bei der Behandlung von P‐haltigen Eisen‐Kohlenstoff‐Schmelzen mit CaC2—CaF2‐Schlacken wird die Entphosphorung ebenfalls über in Lösung gegangenes Ca und die Bildung von Calciumphosphid geregelt. Die Entphosphorung ist stark abhängig vom C‐Gehalt im Eisen und zeigt nach den eigenen Ergebnissen ein Maximum bei ca. 0,85 Gew.‐% C. Jedoch wird durch das verstärkte Auftreten des Calciumcarbophosphids bei höheren Kohlenstoffgehalten auch bei Graphitsättigung der Eisenschmelze noch ein deutlicher P‐Abbau bei steigenden Ca‐Gehalten gewährleistet. Insgesamt führt die Entphosphorungsbehandlung mit CaC2—CaF2‐Schlakken zu Abbauergebnissen, die einer Verschiebung der im reinen System Fe—C—Ca—P gefundenen Sättigungszustände zu um den Faktor 2 niedrigeren Werten gleichkommen.
ISSN:0003-8962
DOI:10.1002/srin.198700239
出版商:Wiley
年代:2016
数据来源: WILEY
|
5. |
Investigation of the kinetics of breakup of gas bubbles in liquid metals with digital simulation method |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 414-420
Saffet Turkan,
Klaus W. Lange,
Preview
|
PDF (545KB)
|
|
摘要:
The method of digital system simulation can be effectively used to quantify the complex multiphase interactions within a gas injection process. Process simulation results yield a better understanding and a better aimed engineering of gas dispersion techniques in metallurgical processes. In this paper the breakup phenomenon of gas bubbles in stagnant liquids is simulated and the dependencies between breakup of bubbles and various parameters of a gas dispersion process such as operative parameters, system parameters and mass transfer rates are investigated.The bubble diameter after breakup is almost independent of the nozzle diameter and gas flow rate. The frequency of bubble breakup and critical bubble size depend on the rate of mass transfer into the bubble. An almost constant rising velocity is achieved only in those cases investigated where mass transfer and bubble breakup are considered. In all other cases no stationary rising velocity is obtained. The interplay between bubble size, rising velocity and the inertia of the surrounding liquid and the influence of mass transfer and breakup are investigated.Simulation results reveal that the behaviour of an ascending bubble is strongly influenced by the mass transfer rate, i. e. by the composition of the melt. Verification of the simulation results with empirical equations from literature shows a very good agreement in all dispersion systems investigated.
ISSN:0003-8962
DOI:10.1002/srin.198700240
出版商:Wiley
年代:2016
数据来源: WILEY
|
6. |
Penetrability of impinging gas jets in molten steel bath |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 421-426
Satish C. Koria,
Klaus W. Lange,
Preview
|
PDF (577KB)
|
|
摘要:
An experimental study is carried out to determine the penetrability of impinging gas jets in molten steel baths of BOF and combined blown steelmaking. Depth and diameter of the depression produced by an impinging single jet or multi‐nozzle jets are measured and correlated successfully with dimensionless momentum flow rate number. The equations are represented in the form of a nomogram by which the depth and diameter of the depression in a molten steel bath during the blow can be determined from easily available top blowing parameters.
ISSN:0003-8962
DOI:10.1002/srin.198700241
出版商:Wiley
年代:2016
数据来源: WILEY
|
7. |
Mathematical model for computer simulation and control of steelmaking |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 427-431
Brahma Deo,
Piyush Ranjan,
Amit Kumar,
Preview
|
PDF (410KB)
|
|
摘要:
A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (Gco). oxygen flux factor (Fo) and emulsification factor (EM). These simulation parameters, when combined with on‐line measurement of off‐gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.
ISSN:0003-8962
DOI:10.1002/srin.198700242
出版商:Wiley
年代:2016
数据来源: WILEY
|
8. |
Properties of through hardening bearing steels produced by BOF blowing metallurgy and by electric arc furnace with ladle metallurgy |
|
Archiv für das Eisenhüttenwesen,
Volume 58,
Issue 9,
2016,
Page 432-438
Rudolf Baum,
Kurt Böhnke,
Tilman Boeckers,
Harald Klemp,
Preview
|
PDF (585KB)
|
|
摘要:
Melting in EAF and BOF‐TBM and different methods of aluminium deoxidation in the subsequent ladle treatment result in a similar degree of cleanness. With respect to micro‐inclusions the air melted ingot and continuous cast steels achieve nearly the same level as remelted steels. Considering macro‐inclusions there still remains a decisive difference: remelted steel is sure to be free from macro‐inclusions, whereas some occasionally occur in air melted steel.The random test and metallographic evaluation systems do not allow uniform classification of the various steel groups. None of the applied methods can determine definite inclusion contents. The number and sizes of the evaluated types of inclusions only can define the statistical probability of their occurrence in a larger lot of heats. Up to now they cannot be related to the fatigue behaviour of the steels. Therefore, further investigation is necessary to reveal the effect of critical sizes and chemistry of the various inclusions on the fatigue behaviour. First tests reveal that the machinability seems to be governed by the carbide grain sizes more than by the sulphur contents in the investigated range of 0.003‐0.015%. The comparison of test results in terms of cleanness and segregation shows that continuous casting should allow the same application as ingot casting.
ISSN:0003-8962
DOI:10.1002/srin.198700243
出版商:Wiley
年代:2016
数据来源: WILEY
|