1. |
Some aspects on MgO solubility in complex slags |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 191-195
Åke Bergman,
Preview
|
PDF (747KB)
|
|
摘要:
A magnesia capacity is defined,CMg2+= (%Mg2+)/aMgOand its relation to optical basicity is examined and discussed. The solubility of MgO in complex slags, in equilibrium with magnesiowustite, is derived from the activity of MgO in the magnesiowustite and from the magnesia capacity as given by the slag's optical basicity. It is found that the activity of MgO in the magnesiowustite can be derived from [%O] assuming ideality in the FeO–MgO system at 1600°C. It is also found that the MgO saturation contents in complex slags are accurately derived from the equation:In addition, the relation between the magnesia capacity and the capacities of vanadium and phosphorus is examined and the relative basicity of the oxides is discussed.
ISSN:0003-8962
DOI:10.1002/srin.198900273
出版商:Wiley
年代:2016
数据来源: WILEY
|
2. |
Untersuchungen über die Auswirkungen unterschiedlicher Verfahrensweisen wie Pulvereinblasen und Pulveraufgabe bei der Entphosphorungsbehandlung von Roheisen mit carbonathaltigen Pulvergemischen |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 196-200
Jürgen Klodt,
Klaus W. Lange (†),
Preview
|
PDF (778KB)
|
|
摘要:
In Laboruntersuchungen am MF‐Induktionsofen wurden Roheisenschmelzen durch kombinierte Verfahrensweisen aus Aufgabe und/oder Einblasen von carbonathaltigen Pulvermischungen, insbesondere Soda, entphosphort. In der vorliegenden Arbeit wird über die Auswirkungen unterschiedlicher Verhältnisse von eingeblasenem zu aufgegebenem Pulver unter gleichbleibenden Rührbedingungen auf die Entfernung von Phosphor, Silicium, Schwefel und Kohlenstoff aus der Schmelze berichtet. Folgende Ergebnisse werden erhalten: Steigende Anteile von eingeblasenem Pulver an der Pulvergesamtmasse fördern die Entsilicierung, Entschwefelung und Entkohlung, jedoch nicht die Entphosphorung. Während der an die Einblasperiode anschließenden Spülperiode laufen bei hohen Anteilen an eingeblasenem Pulver Entsilicierung und Entschwefelung noch weiterhin ab, gleichzeitig tritt eine Rückphosphorung auf. Die Rückphosphorung wird im Fall der vollständigen Pulveraufgabe auf das Bad nicht gefunden. Niedrige Phosphorgehalte im Roheisen werden bei gleichbleibend hohen Kohlenstoffgehalten durch die Pulveraufgabe erreicht. Die Entkohlung beim Pulvereinblasen wird durch CaCO3‐ und Fe2O3‐Anteile der Pulvermischungen stärker begünstigt als durch den Na2CO3‐Anteil.
ISSN:0003-8962
DOI:10.1002/srin.198900274
出版商:Wiley
年代:2016
数据来源: WILEY
|
3. |
Metal flow in compression of tubular parts: predictions made with different computer programs and effect of flow stress data |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 201-207
Gerhard Hirt,
Taylan Altan,
Preview
|
PDF (1120KB)
|
|
摘要:
The study deals with the comparison of three different FEM (finite element method) based codes for simulating the upsetting of a tubular shape. The geometry of this specific part was selected to be very sensitive to variations in flow stress or to errors in the mathematical formulation of metal flow. The results of the study indicated that the available FEM codes are capable of handling two dimensional isothermal and nonisothermal forming problems with reasonable accuracy, provided the input data on flow stress, friction, and heat transfer are also reasonably accurate. Inaccuracies in these data, especially in flow stress, may cause considerable errors in the prediction of metal flow as well as forming loads.
ISSN:0003-8962
DOI:10.1002/srin.198900275
出版商:Wiley
年代:2016
数据来源: WILEY
|
4. |
Temperature field on strip cross‐section during hot rolling |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 208-214
Bogusław Gierulski,
Marek Cierniak,
Preview
|
PDF (857KB)
|
|
摘要:
The present report presents a mathematical model for the computation of temperature variation over cross‐section during hot rolling. In the model discussed the differential equation describing transient heat conduction, where internal heat sources are taken into account, is solved using the method of finite differences. Yield stress distribution along the deformation zone being to be known when determining internal heat source capacity has been found on the basis of methods of heredity theory. The possibilities to apply the method devised have been analysed by computing temperature variation during rolling process, the obtained computation results being then presented in a graphical form.
ISSN:0003-8962
DOI:10.1002/srin.198900276
出版商:Wiley
年代:2016
数据来源: WILEY
|
5. |
Effects of morphology on the tensile and fatigue behaviour of a dual‐phase steel |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 215-220
Zhengming Sun,
Zhongguang Wang,
Suhua Ai,
Preview
|
PDF (1842KB)
|
|
摘要:
Duplex ferrite/martensite microstructures with the same fibrous, network and blocky martensite content (23%) were developed by careful heat treatments. The monotonic and cyclic properties were investigated. The stress‐life behaviour (S–N curves) was also determined. The results demonstrated that, of the three microstructures the fine fibrous structure produced by intermediate quenching is the best in terms of strength and ductility while the network structure developed by intercritical annealing exhibits the worst properties. However, the network structure shows the highest potentiality of cyclic hardening and the fine fibrous the lowest. The network structure has the lowest fatigue limit. The blocky structure, the monotonic behaviour of which is in between, shows the best fatigue life. The fine fibrous structure has a high cycle fatigue life equivalent to that of blocky structure but exhibits the lowest fatigue resistance in the short life range.
ISSN:0003-8962
DOI:10.1002/srin.198900277
出版商:Wiley
年代:2016
数据来源: WILEY
|
6. |
The influence of temperature and strain rate on the stress‐strain behaviour of “in‐situ solidified” steel during tensile test |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 221-229
Guo Xun Liu,
Winfried Dahl,
Preview
|
PDF (1649KB)
|
|
摘要:
The stress‐strain behaviour of a low‐carbon low‐alloyed steel after solidification in‐situ was studied at four temperatures (1000°C, 1150°C, 1300°C and 1400°C) and at four deformation rates (6 mm s−1, 0,6 mm s−1, 0,06 mm s−1and 0,006 mm s−1) by tensile tests. The resulting microstructures after solidification and deformation were examined by scanning electron microscope and optical microscope. The results showed that the crystals developed after solidification in the melted part of the tensile specimen are cellular dendritic, similar to the crystallization mode of steel in continuous casting. It was also shown that slip in the dendritic crystals is the main mode of deformation mechanism in the tensile tests within the temperature range mentioned above, but at higher levels within this temperature range (i.e. 1400°C) and at a low deformation rate (i.e. 0,006 mm s−1) grain boundary migration takes part in the deformation process. The data from the tensile test were analysed.
ISSN:0003-8962
DOI:10.1002/srin.198900278
出版商:Wiley
年代:2016
数据来源: WILEY
|
7. |
Einfluß von Restaustenit auf die Korngröße des Austenits nach der Reaustenitisierung von Stählen für schwere Schmiedestücke |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 230-238
Heinz‐Jürgen Peters,
Gerhard Tacke,
Hans‐Paul Hougardy,
Preview
|
PDF (2645KB)
|
|
摘要:
Die Korngröße des Austenits nach der Reaustenitisierung von Stählen für schwere Schmiedestücke wurde in Abhängigkeit von der Art des Ausgangsgefüges, den Wiedererwärmungsbedingungen und den chemischen Zusammensetzungen untersucht. Besonders wurde der Einfluß von Restaustenit im Ausgangsgefüge auf die Korngröße des Austenits nach erneuter Austenitisierung betrachtet. Nach den Ergebnissen bleibt das Austenitkorn bei der Reaustenitisierung von Gefügen der Martensitstufe und der unteren Bainitstufe grob, wenn bei der Wiedererwärmung werkstoffabhängige Grenzerwärmungsgeschwindigkeiten unterschritten werden. Maßgeblich für eine mit zunehmender Erwärmungsgeschwindigkeit – in Abhängigkeit auch von den örtlichen chemischen Zusammensetzungen – mögliche Austenitkornverfeinerung ist das zeitabhängige Wachsen von Restaustenitfilmen zwischen den Kristalliten des Ausgangsgefüges in Konkurrenz zu den Anlaufzeiten für Keimbildung und ‐wachstum an den Grenzflächen Carbid/Ferrit.Ist wenig oder kein Restaustenit vorhanden, wie in einigen Gefügen der Bainit‐ bzw. der Perlitstufe, so entsteht der Austenit unabhängig von den Wiedererwärmungsbedingungen durch Neubildung und Wachsen von Austenitkeimen an den Grenzflächen Ferrit/Carbid. Unter den gegebenen Versuchsbedingungen entstand dabei immer ein feines Austenitkorn.
ISSN:0003-8962
DOI:10.1002/srin.198900279
出版商:Wiley
年代:2016
数据来源: WILEY
|
8. |
Correction |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 238-238
Preview
|
PDF (106KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198900280
出版商:Wiley
年代:2016
数据来源: WILEY
|
9. |
News from the Max‐Planck‐Institut für Eisenforschung GmbH |
|
Archiv für das Eisenhüttenwesen,
Volume 60,
Issue 5,
2016,
Page 239-240
Preview
|
PDF (342KB)
|
|
ISSN:0003-8962
DOI:10.1002/srin.198900281
出版商:Wiley
年代:2016
数据来源: WILEY
|