1. |
The operation and performance of a groove-type chip forming device |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 529-558
B. WORTHINGTON,
Preview
|
PDF (987KB)
|
|
摘要:
When cutting with double rake angle tools it is known that the configuration of the dead metal zone that may form, influences the surface roughness and sub-surface deformation of the workpiece. The effect of changes in cutting conditions on the configuration of this dead metal zone is reported.
ISSN:0020-7543
DOI:10.1080/00207547608956623
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
2. |
Design of a high-frequency dynamometer for cylindrical grinding |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 559-568
B. K. NAGPAL,
S. K. BHATTACHARYYA,
Preview
|
PDF (336KB)
|
|
摘要:
This paper describes the basic concepts and constructional details of a piezoelectric high-frequency dynamometer for cylindrical grinding. Resultant response is presented with a set of typical force spectra for different dressing rates. Based on the power contained within a frequency band, a technique for predicting the wheel life is put forward.
ISSN:0020-7543
DOI:10.1080/00207547608956624
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
3. |
An experimental investigation of the variation of peak torque and power in gear hobbing |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 569-581
D. A. MILNER,
H. RAAFAT,
Preview
|
PDF (371KB)
|
|
摘要:
Some aspects, by a statistical approach, of the variation of the peak torque and mean cutting power encountered in gear hobbing are presented here. The cutting torque is measured by a purpose built strain gauge dynamometer and a wattmeter evaluates the power consumed. The problem is to determine whether a host of independent variables such as axial feed, module, material hardness, number of teeth in the gear blank and hobbing speed have a significant influence on the dependent variables, maximum cutting torque and average power. Mathematical models are constructed giving the relationship between these variables and the results indicate that the cutting speed has a significant influence on both the peak torque and average power. This significant point has not previously been noted for this type of process.
ISSN:0020-7543
DOI:10.1080/00207547608956376
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
4. |
An applied model for the facilities design problem |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 583-595
JAMESA. TOMPKINS,
RUDDELL REED,
Preview
|
PDF (568KB)
|
|
摘要:
A model ia described which can be used to assist in the design of a facility, where the facilities design includes the selection of the materials handling system and the placement of departments within the facility. The model is entitled COFAD, an acronym representing Computerized FAcilities Design. COFAD selects the facilities design which approaches the minimal materials handling system cost. The input requirements and the utilization of COFAD are demonstrated via an example problem. Although it is shown that the model results in good solutions, due to the complexity of the design problem, no claim of optimality can be made.
ISSN:0020-7543
DOI:10.1080/00207547608956377
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
5. |
The production capacity of job shops with limited storage space |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 597-605
J. A. BUZACOTT,
Preview
|
PDF (397KB)
|
|
摘要:
Suppose the number of jobs which can be stored in front of the machines in a job shop is limited. As a result, arriving jobs for which there is no space in the shop will form a shop queue. The production capacity or maximum departure rate of jobs from the shop will depend on the way in which jobs are selected from the shop queue for release to the machine queues. For a job shop with two identical machines and random routing of jobs a number of release rules are compared. It is shown that the production capacity is increased when the number of jobs in the shop is kept less than the available storage space. Among release rules independent'of job processing times and number of operations the optimum release rule is shown, using dynamic programming, to be the idle machine rule, i.e. only release a job to the shop when a machine would otherwise be idle.
ISSN:0020-7543
DOI:10.1080/00207547608956378
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
6. |
Simulation studies of conveyor-paced assembly lines with buffer capacity |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 607-624
G. M. BUXEY,
D. SADJADI,
Preview
|
PDF (733KB)
|
|
摘要:
A simulation, model has been developed to describe an assembly line where items are removed from a conveyor belt for processing and returned for transportation to subsequent work stations. Output characteristics are presented for the case where operator's work-time distributions can be approximated to a normal curve, and the analysis is made so as to generalize the results over a useful range of tolerance, feed interval and mean service times. In particular, the effect of buffer capacity on line performance, and its relevance to tolerance time, is studied.
ISSN:0020-7543
DOI:10.1080/00207547608956379
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
7. |
Extensions to the coil slitting problem |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 625-630
DONR. COFFIELD,
ROBERTM. CRISP,
Preview
|
PDF (248KB)
|
|
摘要:
The problem of slitting coils of some material (steel, paper, etc.) into smaller widths is considered in this paper. An extended linear programming model is presented that considers inventory and production scheduling aspects in addition to trim loss. The L.P. model produces an optimum slitting schedule that minimizes trim and inventory costs subject to several common production and material constraints. A plan for implementing the model is presented.
ISSN:0020-7543
DOI:10.1080/00207547608956380
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
8. |
An ordered flow-shop sequencing problem with mean completion time criterion† |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 631-635
S. S. PANWALKAR,
A. W. KHAN,
Preview
|
PDF (178KB)
|
|
摘要:
This paper investigates a subcategory of the classical n job m machine problem in which the processing times of different jobs are ' ordered '. An extremely simple algorithm is presented which obtains a sequence minimizing the mean completion time of all jobs. The proof of optimality is presented in the Appendix. The problem illustratos that although no efficient procedure exists to solve the classical flow-shop problem with the mean completion time criterion, it is possible to develop such a procedure for a specially structured problem.
ISSN:0020-7543
DOI:10.1080/00207547608956381
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|
9. |
Review of: “Statistical Methods for Quality Control”. By A. K. S. Jardine, J. D. Macfablane and C. S. Greensted. (London: Heinemann, 1975.) [Pp. 176.] Price £4-00 (limp). |
|
International Journal of Production Research,
Volume 14,
Issue 5,
1976,
Page 637-637
Preview
|
PDF (25KB)
|
|
ISSN:0020-7543
DOI:10.1080/00207547608956382
出版商:Taylor & Francis Group
年代:1976
数据来源: Taylor
|