|
1. |
Effect of ammonia plasma treatment on plasma deposited silicon nitride films/silicon interface characteristics |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 831-834
Hitoshi Arai,
Keiji Tanaka,
Shigeto Kohda,
Preview
|
PDF (364KB)
|
|
摘要:
The properties of silicon nitride film obtained by plasma‐assisted chemical vapor deposition (plasma CVD) are studied along with the effect of NH3plasma treatment on plasma CVD silicon nitride/silicon interface characteristics. With this NH3plasma treatment of the silicon surface before silicon nitride film deposition, the interface state densities of the silicon nitride/silicon interface are reduced to about 1010cm−2 eV−1and the hysteresis voltage of the capacitance–voltage (C–V) curve is reduced to 0.1 V. These improvements are most pronounced when there is a large H concentration in the silicon nitride film. However, no effect is observed when N2or H2plasma was used instead of NH3plasma. Auger electron spectroscopy analysis of the silicon surface after NH3plasma treatment shows that nitrogen is incorporated in the near surface region of the silicon substrate. This implies that nitridation of the silicon surface occurs due to NH3plasma treatment and the interface characteristics are improved because the silicon nitride/silicon interface is made inside the silicon substrate due to this nitridation.
ISSN:1071-1023
DOI:10.1116/1.584349
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
2. |
Improved GaAs substrate temperature measurement during molecular‐beam epitaxial growth |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 842-845
S. L. Wright,
R. F. Marks,
A. E. Goldberg,
Preview
|
PDF (384KB)
|
|
摘要:
We describe an improvement in optical pyrometry of GaAs substrates, by restricting the pyrometer wavelength to a band of 0.91 to 0.97 μm. This allows temperature measurement of nonbonded GaAs wafers during molecular‐beam epitaxial growth, without interference from the radiation emitted by the substrate heater. Error‐free readings have been obtained for substrate temperatures as low as 440 °C, which is particularly important for the automated growth of alloys such as (In,Ga)As. By detecting a larger substrate surface area and using a calibration curve, the useful measurement range can be extended even lower.
ISSN:1071-1023
DOI:10.1116/1.584351
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
3. |
Planar quantum wells with spatially dependent thicknesses and Al content |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 846-849
W. D. Goodhue,
J. J. Zayhowski,
K. B. Nichols,
Preview
|
PDF (353KB)
|
|
摘要:
We have developed a process using molecular‐beam epitaxy for growing GaAs/AlGaAs quantum wells with thicknesses and Al content that vary in a controlled manner on (100)‐oriented GaAs substrates. The control is accomplished by manipulating the Ga sticking coefficient through local variations of the substrate temperature. To indicate the range of thickness and Al content variations that can be achieved, we show that exciton peak energies of the quantum wells can be made to vary as much as 200 meV between predetermined locations<2 mm apart on the wafer. The quality of the exciton spectra is good throughout, indicating good quality epitaxial layers throughout. This process allows flexibility in designing the well dimensions and composition in various regions of the wafer and could lead to a variety of important developments in GaAs devices.
ISSN:1071-1023
DOI:10.1116/1.584307
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
4. |
Submicron patterned doping of GaAs using a thin solid Si dopant source by transient excimer laser melting |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 850-852
Koji Sugioka,
Koichi Toyoda,
Preview
|
PDF (325KB)
|
|
摘要:
Patterned doping of GaAs using a thin solid Si dopant source by pulsed excimer laser melting is described. Linewidths as narrow as 0.3 μm are demonstrated. The power‐dependent linewidth of the doped region agrees well with calculations of transient heat conduction in the substrate.
ISSN:1071-1023
DOI:10.1116/1.584308
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
5. |
Resist heating effect in direct electron beam writing |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 853-857
Takayuki Abe,
Kenji Ohta,
Hirotsugu Wada,
Tadahiro Takigawa,
Preview
|
PDF (566KB)
|
|
摘要:
A new model for the analysis of resist heating is proposed and applied to the direct electron beam writing method using a variably‐shaped electron beam system and a single‐layer resist. From calculations based on the present model and experiment, it was found that the resist heating effect leads to resist ablation, difference in resist sensitivity between single exposure and multiple exposures, and depth dependence and beam size dependence of resist sensitivity. It also explains the degradation of shaped beam stitching accuracy as well as pattern size error. The resist heating effect is more serious for direct writing than the estimation obtained from a conventional model. In order to realize submicron patterns below 0.5 μm with considerable high throughput, the use of a highly sensitive resist is essential for overcoming the resist heating effect.
ISSN:1071-1023
DOI:10.1116/1.584309
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
6. |
Oxidation effect on an x‐ray induced reaction of a polyolefinsulfone‐type resist |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 858-861
Kozo Mochiji,
Yasunari Soda,
Takeshi Kimura,
Preview
|
PDF (313KB)
|
|
摘要:
The effect of ambient atmospheric conditions during x‐ray exposure on the sensitivity of a new type positive resist, which contains poly(2‐methylpentene‐1‐sulfone) as the radiation‐sensitive compound, is studied. Resist sensitivity to x rays is seen to depend strongly on oxygen pressure during exposure. Sensitivity in air is only one‐sixth of that in a vacuum. Using Fourier transform infrared spectral analysis of the resist film following x‐ray irradiation, it is found that the alkyl radical of poly(2‐methylpentene‐1‐sulfone) generated by x‐ray irradiation is easily scavenged by the oxygen molecule in air, thus retarding its further unzipping decomposition.
ISSN:1071-1023
DOI:10.1116/1.584310
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
7. |
Effects of partial coherence on contact hole projection lithography |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 862-865
L. K. White,
Preview
|
PDF (367KB)
|
|
摘要:
Calculated image intensity profiles (IIP’s) are presented for contact holes printed with partial coherence levels in theS=0.5 toS=0.7 range and are compared to IIP’s of the correspondingly dimensioned line–space gratings. Improvements in the depth of focus (DOF) latitude and resolution at higher coherence levels (lower pupil fillS) are quantified for contact hole projection lithography with high‐numerical aperture (NA),g‐line lenses. The relationship between contact and grating DOF is quite complex and changes with the coherence level. Higher pupil fills produce greater differences between the contact and grating DOF. Workable contact hole resolution levels for 0.7, 0.6, and 0.5 pupil fills are estimated to occur atkfactors of 0.89, 0.83, and 0.79, respectively, where thekfactor normalizes feature size to the resolution factor λ/NA of the lens.
ISSN:1071-1023
DOI:10.1116/1.584311
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
8. |
Submicron pattern dimension determination using a total waveform comparison method |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 866-870
Shinya Hasegawa,
Yasuo Iida,
Toshiharu Hidaka,
Preview
|
PDF (450KB)
|
|
摘要:
A pattern dimension determination method has been developed. The three parameters, linewidth, wall angle, and film thickness represent pattern dimension. The total waveform of a measured backscattered electron signal is compared with a standard signal data base. Two methods are adopted to reduce data base construction time. (1) The data base was constructed with Monte Carlo simulation by a supercomputer. (2) Data base size is reduced using a waveform approximation method. The two improvements result in fast data base construction (26 min) for a specified material sample. This data base construction method is more practical than preparing signal data base from real standard sample due to data base construction time. Obtained dimensional accuracies are found to be 0.02 μm, 5 deg, and 0.1 μm for linewidth, wall angle, and film thickness, respectively, with scanning electron micrograph comparisons. Deduction time for obtaining physical dimensions from a signal was 17 s.
ISSN:1071-1023
DOI:10.1116/1.584312
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
9. |
Errors in registration mark detection for electron lithography |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 871-875
S. J. Erasmus,
G. Holley,
Preview
|
PDF (515KB)
|
|
摘要:
Registration marks for electron lithography are usually detected by scanning with an electron beam and measuring the backscattered electron (BE) signal. If the registration mark is on the axis of the lithography tool, the BE signal is symmetric and the mark position may be found accurately. Practical electron lithography often requires that registration marks be found off axis, for example, near the edges of an exposure field. In this case, it is shown by both experiment and Monte Carlo calculation that the registration signals become asymmetric which causes registration errors. It is also shown that these errors can be reduced by a suitable choice of BE detector shape and position.
ISSN:1071-1023
DOI:10.1116/1.584313
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
10. |
Characterization of damage on GaAs in a reactive ion beam etching system using Schottky diodes |
|
Journal of Vacuum Science&Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena,
Volume 6,
Issue 3,
1988,
Page 876-879
S. Sugata,
K. Asakawa,
Preview
|
PDF (386KB)
|
|
摘要:
Chlorine (Cl2) reactive ion beam etching (RIBE)‐induced damage on the GaAs wafer has been characterized by studing the characteristics of Schottky diodes fabricated on the etched surfaces. The ideality factors and the Schottky barrier heights measured by the current–voltage characteristics for ion extraction voltage range from 30 to 200 V at Cl2gas pressure of 2×10−3Torr and are comparable to those of the reference sample cleaned by HCl. Both thenvalue and the barrier height degrade for ion extraction voltage of more than 300 V. For higher Cl2gas pressure, the damage on the etched surface is less. These results suggest that with the low‐energy ions and high‐Cl2gas pressure, the damage of the GaAs surface is reduced significantly. The electron deep levels induced by RIBE disappear after annealing at 400 °C for 10 min.
ISSN:1071-1023
DOI:10.1116/1.584314
出版商:American Vacuum Society
年代:1988
数据来源: AIP
|
|