|
1. |
Metallkundliche und elektronische Untersuchungen über die interkristalline Korrosion an einer AlMg‐9,56 Knetlegierung |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 529-535
U. Rohlfs,
H. Kaiser,
H. Kaesche,
Preview
|
PDF (1229KB)
|
|
摘要:
AbstractEs wurde die interkristalline Korrosion einer 50% kaltgewalzten AlMg‐9,56 Knetlegierung in 1 normaler Natriumchloridlösung in Abhängigkeit von der Wärmebehandlung untersucht. Von den durch die Wärmebehandlungen erzeugten Korngrenzenausscheidungen wurden elektronenmikroskopische Durchstrahlungsaufnahmen angefertigt. Für die Untersuchung der elektrochemischen Eigenschaften wurden die potentiostatische und die galvanostatische Meßmethode angewandt. Das Korrosionsverhalten einer heterogenen Legierung mit hohem Anteil an intermetallischer AlMg‐ß‐Gleichgewichtsphase wurde mit dem von wärmebehandelten Proben der Knetlegierung verglichen. Von der ß‐Gleichgewichtsphase konnte eine Stromspannungskurve bestimmt werden. Es wurden Hinweise auf zwei verschiedene, vom Potential abhängige, geschwindigkeitsbestimmende Reaktionen sowohl für die Auflösung der ß‐Gleichgewichtsphase als auch für die der Korngrenzenausscheidungen der wärmebehandelten Knetlegierung gefunden. Im Verlauf der Wärmebehandlung werden zwei verschiedene Ausscheidungsformen mit unterschiedlichem Korrosionsverhalten beobachtet. Nach kurzer Wärmebehandlungsdauer sind die Korngrenzen von einer kontinuierlichen Ausscheidung belegt, deren Zusammensetzung ungeklärt ist. Nach längerem Auslagern koaguliert diese Ausscheidung zu einzeln stehenden Globuliten aus intermetallischer ß‐Gleichgewichtsphase. Die interkristalline Korrosion der AlMg‐9,56 Knetlegierung wird immer durch die selektive Korrosion der gebildeten Korngr
ISSN:0947-5117
DOI:10.1002/maco.19790300802
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
2. |
The oxidation behaviour of an aligned Ni‐Al‐Cr3‐C2eutectic alloy under isothermal and thermal cycling conditions |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 536-541
J. G. Fountain,
G. C. Wood,
F. H. Stott,
Preview
|
PDF (848KB)
|
|
摘要:
AbstractThe isothermal and thermal cycling oxidation behaviour of a directionally solidified Ni‐Al‐Cr3C2eutectic alloy at temperatures from 800° to 1200 °C in flowing air have been investigated using several physical techniques. At all temperatures an initial, protective, external layer of α‐Al2O3develops on the alloy surface. However, this breaks down mechanically during thermal cycling, enabling a less protective Cr2O3‐rich scale to form.The time of retention of the α‐Al2O3layer at temperature decreases with increasing temperature, failing after between 30 min and 2 h at 1100° and 1200 °C. However, if platinum metal is introduced into the hot zone at these temperatures, this period is increased to about 48 h.Following formation of the external Cr2O3scale, internal oxide penetration into the alloy can be considerable, involving preferential oxide penetration down the alloy/carbide fibre interfaces. Thermal cycling does not influence markedly the oxidation behaviour, although it does result in formation of a greater quantity of nickel‐rich oxide nodules on the scale surface following crack development in the Cr2O3‐rich scale. This crack development is assisted by differential thermal c
ISSN:0947-5117
DOI:10.1002/maco.19790300803
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
3. |
Untersuchungen über den Einfluß der Grundbeschichtung auf Elementbildung und Blasenanfälligkeit von mit Teerpech‐Epoxidharz beschichtetem Stahl in Salzlösungen |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 542-550
H. Hildebrand,
W. Schwenk,
Preview
|
PDF (892KB)
|
|
摘要:
AbstractUnlegierte Stahlbleche wurden in den Zuständen gestrahlt, feuer‐ oder spritzverzinkt, mit vier verschiedenen Stoffen grundiert und mit Teerpech‐Epoxidharz in vier Schichtdicken beschichtet. Die Proben wurden über zwei Jahre in NaCl‐Lösungen ausgesetzt und dabei Potentiale und Widerstände sowie Ströme zu externen Stahlproben gemessen. Anschließend wurde der Korrosionsumsatz an den externen Proben sowie an Verletzungen ausgemessen. Ein wesentliches Kriterium für die Korrosionsschutzwirkung ist der Beschichtungswiderstand, der im allgemeinen erst nach 3 bis 6 Monaten gemessen werden kann. Mit abnehmendem Widerstand steigt die Neigung zur Blasenbildung stark an. Ferner werden durch Elementbildung Poren und unbeschichteter Stahl im Kontakt mit beschichtetem Stahl anodisch gefährdet. Eine gute Korrosionsschutzwirkung haben Beschichtungen mit mehr als 400 m̈m Schichtdicke sowie Grundierungen mit Zn‐Epoxidharz und Zn‐Äthylsilikat, während Alkalisi
ISSN:0947-5117
DOI:10.1002/maco.19790300804
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
4. |
Environmental aspects of stress corrosion crack growth in austenitic stainless steel |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 551-553
B. Eremi,
V. A. Maričev,
Preview
|
PDF (323KB)
|
|
摘要:
AbstractStress corrosion crack velocity and stress corrosion threshold stress intensity have been measured for 18Cr–10Ni–0,5Ti stainless steel in relation to environmental variations. These studies showed that both stage I and stage II growth rate dependence on K are influenced by environmental variations. The chemical composition of the solution being tested, the corrosion‐active components concentration and temperature that influence corrosion kinetics, all influence SCC susceptibility through their effects on overall film stability and localisation of corrosion. The influence of environmental factors on protective film stability was suggested to be an explanation for different values of stress corrosion threshold stress intensity found for different test condi
ISSN:0947-5117
DOI:10.1002/maco.19790300805
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
5. |
Effects of temperature on the Corrosion of copper in sea water at different hydrostatic pressures |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 554-558
E. D. Mor,
A. M. Beccaria,
Preview
|
PDF (469KB)
|
|
摘要:
AbstractAn investigation has been made of the effect which an increasing hydrostatic pressure may have on copper corrosion at different temperatures in sea water at pH 7.8.The tests were carried out at a pressure of 1, 50, 100, 200 and 300 atm at a temperature of 5 °, 10 ° and 20 °C.The pressure set in which the tests were effected was pressurized by an hydropneumatic pump and it was fitted not only with a work electrode, but also with two Pt and one Ag‐AgCl reference electrodes for electrochemical tests.It was found that copper corrosion is always stimulated by a pressure rise and that the increased corrosion rate is accelerated by increasing temperatures.The maximum increase (71%) was obtained at T = 20 °C; D.O = 7.0 ppm and pH = 7.8 at a pressure of 150 atm.But at a temperature of approx. 5 °C, the maximum increase did not exceed 30% always at a pressure of 150 atm.The test findings also evidenced that at a temperature ≤ of 10 °C, the pressure rise did not affect the anodic process but only the cathodic reduction, whereas the anodic process too was significantly accelerated at 20 °C and the influence of the pressure was found to be more a
ISSN:0947-5117
DOI:10.1002/maco.19790300806
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
6. |
Ergebnisse des Forschungs‐ und Entwicklungsprogramms „Korrosion und Korrosionsschutz”︁ |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 559-566
Preview
|
PDF (1143KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19790300807
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
7. |
ACHEMA '79 – Teil 1: Nichtmetallische Werkstoffe – Oberflächenbehandlung und Labortechnik |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 567-572
Chr. Gg. Enke,
Preview
|
PDF (942KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19790300808
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
8. |
Aus Industrie und Technik |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 573-574
Preview
|
PDF (340KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19790300809
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
9. |
Umschau |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 575-578
Preview
|
PDF (518KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19790300810
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
10. |
Corrosion and materials testing |
|
Materials and Corrosion,
Volume 30,
Issue 8,
1979,
Page 579-581
Preview
|
PDF (466KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19790300811
出版商:WILEY‐VCH Verlag GmbH
年代:1979
数据来源: WILEY
|
|