|
1. |
Some factors influencing the adherence of oxides on metals |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 855-859
R. F. Tylecote,
W. K. Appleby,
Preview
|
PDF (1349KB)
|
|
摘要:
AbstractSome of the differences in adherence behaviour may be explained by differences in the respective physical properties of the films and the metals. The strength and plasticity of some of the oxides has been measured; the relative expansion coefficients are also important and it is thought to be the favourable nature of this which is responsible for the good adherence of NiO on nickel and more complex films on nickel‐base alloys.Another important factor is internal stress. The sources of stresses during the oxidation of copper have been estimated using a unilateral oxidation technique. With sufficient knowledge of the mechanical properties it is possible to calculate the actual stress levels in the growing oxide film.A further factor influencing adherence is the accumulation of trace or residual elements on the metalloxide interface. The technique of Peters and Engell has been used to estimate the effect of various elements at a concentration of 0.4 wt% on the adherence of scales on iron. The results fall into four groups; those that form mixed oxide scales with wüstite either spalled or were weakly adherent; those on noble metal alloys were nearly comparable with pure iron, but copper and tin had a detrimental effect. Scales containing As, Sb and P were weakly adherent but left a thin adherent layer on the metal surface. Cobalt and niobium had no effe
ISSN:0947-5117
DOI:10.1002/maco.19720231002
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
2. |
Strain/Oxidation Interactions in Steels and Model Alloys |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 859-870
D. R. Holmes,
R. T. Pascoe,
Preview
|
PDF (2087KB)
|
|
摘要:
AbstractStrain/oxidation interactions in steels and model alloys The strains generated in oxide films on a number of materials of interest to the power generation industry are considered in relation to their operating conditions. Topics discussed the growth of nuclear canning alloys, oxide spalling, the formation of multilayer oxides during internal boiler corrosion and low ductility failures in austenitic stainless steels. The strains induced during thermal cycling are considered in detail and the temperature changes required to cause film craking are estimated and compared with observed spalling behaviour.
ISSN:0947-5117
DOI:10.1002/maco.19720231003
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
3. |
Einige Gesichtspunkte zur Haftung von Zunder auf Stählen bei hoher Temperatur |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 870-875
H. Trenkler,
Preview
|
PDF (2220KB)
|
|
摘要:
AbstractUnter den beim Warmwalzen herrschenden Bedingungen (etwa 1000°C) wird die experimentelle Bestimmung der Haftfestigkeit des Zunders schwierig, so daß keine eindeutigen Aussagen über den Reinheitsgrad der Walzgutoberfläche möglich ist. Die Schwierigkeiten sind dadurch bedingst, daß die Grenzfläche zwischen Zunder und stahl sebr unterschiedlich ausgebildet ist. Je rauher die Grenzfläche, desto besser die Zunderhaftung. Hierbei spielt einmal die Temperatur eine wichtige Roll: die Grenzfläche von bei 1000°C verzundertem Stahl ist wesentlich rauher als die von Reineisen, während bei 1200°C kein Unterschied mehr festzustellen ist. Auch SO2‐Gehalte in der Atmosphäre erhöhen die Rauhigkeit der Grenzfläche erhöhen die Rauhighkeit der Grenzfläche, hauptsächlich wegen der Bildung flüssiger Phasen und der damit verbundenen starken Ionisierung der Korngrenzen. Hierbei spielen auch die Begleitelemente (C, Si, Cu) eine Rolle, doch läßt sich weder für einzelne dieser Elemente noch für deren Kombinationen eine eindeutige Aussage bezüglic
ISSN:0947-5117
DOI:10.1002/maco.19720231004
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
4. |
Influence de l'adherence de la calamine sur la concentration du carbone au voisinage de la surface des aciers |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 876-880
J. Baud,
J. P. Blumensi,
J. Manenc,
Preview
|
PDF (1806KB)
|
|
摘要:
AbstractL'oxydation d'alliages FeC peut théoriquement se produire avec décarburation ou carburation, suivant la tempéature et les pressions partielles de l'oxyde de carbone et du gaz carbonique dans l'atmosphère. Dans les conditions usuelles, seule la décarburation se produit. Cependant, un enrichissement superficiel, temporaire, en carbone peut exister en déipt des prévisions theéoriques. Ce dernier effet est très important entre 730 et 800°C; il disparaît au‐dessus de 950°C. L'enrichissement n'a lieu qu'aux endroits où la calamine est adhérente. L'oxyde est traversé par les ions ferreux qui contribuent à sa croissance, mais il est imperméable au carbone. Des essais de mise en solution dans le protoxyde de fer de carbone marqué ont montre que la soubilité de cet élément dans cet oxyde est inférieure à 0,5 ppm.La décarburation se produit localement à l'endroit des défauts de surface et se propage par suite du décollement progressif de la calamine.La présence de silicium, de manganèse ou de nickle, favorise le décollement des couches d'oxyde et en conséquence la décarburation du métal sous‐jacent.Dans le cas du silicium et pour les temps de traitement les plus longs, plusieurs décollements successifs ont lieu, les couches externes étant constituées uniquement d'hématite et de magnétite. Dans le cas du manganése, la couche de calamine est toujours décollée, soit à chaud et l'on observe une suroxydation, soit à froid. Dans le cas du nickel, la couche mixte qui se trouve à li'interface, et qui est fortement enrichie en nickel métallique, adhére aumétal sous‐jacent. Un décollement a lieu entre cette couche mixte et le protoxyde. La couche mixte étant poreuse, on observ
ISSN:0947-5117
DOI:10.1002/maco.19720231005
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
5. |
Zur Haftfestigkeit von Walzzunder auf unlegiertem Stahl |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 880-886
M. Spangenberg,
Preview
|
PDF (1124KB)
|
|
摘要:
AbstractMit 3 verschiedenen Werkstoffen (Armco‐Eisen, Stahl mit 0,5 und 0,6 % Mn und 0,1 bzw. 0,5% C) wurden Oxidations‐ und Walzversuche durchgeführt, wobei die Verformungsgrade zwischen 5 und 60% lagen. Die Haftfestigkeit des Zunders läßt sich danach nicht mit einer Größe definieren, man muß Schichtdicke, Walztemperatur und Verformungsgrad gemeinsam berücksichtigen; der Einfluß der drei Größen nimmt in der angegebenen Reihenfolge ab. Die Haftfestigkeit steigt generell mit wachsender Schichtdicke, zunehmender Walztemperatur. Dabei spielt auch eine Rolle, daß bei niedrigen Walztemperaturen die Härtedifferenz zwischen Zunder und Metall größer ist. Der Verlauf der Haftfestigkeit läßt sich im untersuchten Bereich (Walztemperatur 800 bis 1000°C) durch eine lineare Funktion, gebildet aus den drei genannten Einflußgrößen, mit ausreichender
ISSN:0947-5117
DOI:10.1002/maco.19720231006
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
6. |
The structure and adhesion of oxide scales on FeNiMo and FeCrMo alloys |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 886-893
R. Rolls,
F. V. Arnold,
Preview
|
PDF (1852KB)
|
|
摘要:
AbstractThe Structure and Adhesion of Oxide Scales on FeNiMo and FeCrMo Alloys A preliminary study has been made of the structure and adhesion of oxide scales formed on Fe‐1.8 wt.% Ni‐0.3wt.% Mo and Fe‐1wt.% Cr‐0.5wt.% Mo in oxygen at 930°–1250°C.From 930°–1250°C, the FeNiMo alloy oxidised at a slower rate that the FeCrMo alloy, and both alloys oxidised at a slower rate than high‐purity iron.Hot bend tests and hot tensile tests of a scale‐metal joint revealed that the scales comprised a strongly adherent inner layer (enriched in CrMo or Ni) and a weakly coherent bulk structure.In the FeNiMo alloy, failure in the bulk scale occured along a smooth plane at the edge of the Ni‐enrichment zone whereas in contras, for the FeCrMo alloy, failure occured withing the CrMo en
ISSN:0947-5117
DOI:10.1002/maco.19720231007
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
7. |
Caractérisation à l'aide de la microsonde éléctronique des couches de corrosion sur aciers faiblement alliés exposés aux gaz de combustion |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 893-901
E. Gadda,
M. Livraghi,
V. Regis,
Preview
|
PDF (3552KB)
|
|
摘要:
AbstractDes èchantillons de tubes en acier faiblement alliés, du type 13CrMo44, ont été ex psés;prs d'une campagne de corrosion de 1000 heures aux gaz de combustion d'une four expérimental brûlant du mazout BTS et fonctionnant à fort excè d'air (∼ 30%).Analysées à l'aide d'une microsonde électronique, les couches de corrosion ont puêtre caractérisées par la distribution et le profil de concentration des principaux éléments intervenant dans le processus de corrosion: fer, oxygène, chrome soufre, vanadium, sodium, calcium.La présence de soufre et l'enrichissement en chrome observés dans la première couche de corrosion, en particulier à l'interface métal‐oxyde, est discutée du point de vue de l'influence possible de ces deux éléments sur l
ISSN:0947-5117
DOI:10.1002/maco.19720231008
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
8. |
Aus Industrie und Technik |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 902-911
Preview
|
PDF (2097KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19720231009
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
9. |
Umschau |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 911-922
Preview
|
PDF (2092KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19720231010
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
10. |
Veröffentlichung von Vorträgen |
|
Materials and Corrosion,
Volume 23,
Issue 10,
1972,
Page 922-922
Preview
|
PDF (141KB)
|
|
ISSN:0947-5117
DOI:10.1002/maco.19720231011
出版商:WILEY‐VCH Verlag GmbH
年代:1972
数据来源: WILEY
|
|