|
1. |
The Obstacle-Set Method for Representing Muscle Paths in Musculoskeletal Models |
|
Computer Methods in Biomechanics and Biomedical Engineering,
Volume 3,
Issue 1,
2000,
Page 1-30
BRIANA. GARNER,
MARCUSG. PANDY,
Preview
|
PDF (1267KB)
|
|
摘要:
A computational method is introduced for modeling the paths of muscles in the human body. The method is based on the premise that the resultant muscle force acts along the locus of the transverse cross-sectional centroids of the muscle. The path of the muscle is calculated by idealizing its centroid path as a frictionless elastic band, which moves freely over neighboring anatomical constraints such as bones and other muscles. The anatomical constraints, referred to as obstacles, are represented in the model by regular-shaped, rigid bodies such as spheres and cylinders. The obstacles, together with the muscle path, define an obstacle set. It is proposed that the path of any muscle can be modeled using one ox more of the following four obstacle sets: single sphere, single cylinder, double cylinder, and sphere-capped cylinder. Assuming that the locus of the muscle centroids is known for an arbitrary joint configuration, the obstacle-set method can be used to calculate the path of the muscle for all other joint configurations. The obstacle-set method accounts nol only for the interaction between a muscle and a neighboring anatomical constraint, but also for the way in which this interaction changes with joint configuration. Consequently, it is the only feasible method for representing the paths of muscles which cross joints with multiple degrees of freedom such as the deltoid at the shoulder.
ISSN:1025-5842
DOI:10.1080/10255840008915251
出版商:Taylor & Francis Group
年代:2000
数据来源: Taylor
|
2. |
Analysis of Time-Varying Biological Data Using Rainflow Cycle Counting |
|
Computer Methods in Biomechanics and Biomedical Engineering,
Volume 3,
Issue 1,
2000,
Page 31-40
CHRISTOPHERR. JACOBS,
CLARE E. YELLOWLEY,
DREW V. NELSON,
HENRY J. DONAHUE,
Preview
|
PDF (466KB)
|
|
摘要:
A wide range of biological investigations lead to time-history data. The characterization of such data can be difficult particularly in the presence of signal noise or superimposed signals. Several methods are described which can be brought to bear including FFT, thresholding, peak counting, and range counting. However, each of these approaches has significant disadvantages. In this paper we describe a novel method, known as rainflow cycle counting, for characterizing time varying biological time-history data in terms of spiking or oscillation amplitude and frequency. Rainflow counting is a straightforward algorithm for identifying complete cycles in the data and determining their amplitudes. The approach is simple, reliable, easily lends itself to automation, and robust even in the presence of superimposed signals or background noise. After describing the method, its use and behavior are demonstrated on three sample histories of intracellular calcium concentration in chondrocytes exposed to fluid shear stress. The method is also applied to a more challenging data set that has had an artificial random error included. The results demonstrate that the rainflow counting algorithm identifies signal oscillations and appropriately determines their amplitudes even when superimposed or distorted by background noise. These attractive properties make rainflow counting a powerful approach for quantifying and characterizing biological time histories.
ISSN:1025-5842
DOI:10.1080/10255840008915252
出版商:Taylor & Francis Group
年代:2000
数据来源: Taylor
|
3. |
A Mathematical Formulation for 3D Quasi-Static Multibody Models of Diarthrodial Joints |
|
Computer Methods in Biomechanics and Biomedical Engineering,
Volume 3,
Issue 1,
2000,
Page 41-64
S.D. KWAK,
L. BLANKEVOORT,
G.A. ATESHIAN,
Preview
|
PDF (1544KB)
|
|
摘要:
This study describes a genera] set of equations for quasi-static analysis of three-dimensional multibody systems, with a particular emphasis on modeling of diarthrodial joints. The model includes articular contact, muscle forces, tendons and tendon pulleys, ligaments, and the wrapping of soft tissue structures around bone and cartilage surfaces. The general set of equations governing this problem are derived using a consistent notation for all types of links, which can be converted conveniently into efficient computer codes. The computational efficiency of the model is enhanced by the use of analytical Jacobians, particularly in the analysis of articular surface contact and wrapping of soft tissue structures around bone and cartilage surfaces. The usefulness of the multibody model is demonstrated by modeling the patellofemoral joint of six cadaver knees, using cadaver-specific data for the articular surface and bone geometries, as well as tendon and ligament insertions and muscle lines of actions. Good accuracy was observed when comparing the model patellar kinematic predictions to experimental data (mean ± stand, dev. error in translation: 0.63 ± 1.19 mm, 0.10 ± 0.71 mm, -0.29 ± 0.84 mm along medial, proximal, and anterior directions, respectively; in rotation: -1.41 ± 1.71°, 0.27 ±2.38°, -1.13 ± 1.83° in flexion, tilt and rotation, respectively). The accuracy which can be achieved with this type of model, and the computational efficiency of the algorithm employed in this study may serve in many applications such as computer-aided surgical planning, and real-time computer-assisted surgery in the operating room.
ISSN:1025-5842
DOI:10.1080/10255840008915253
出版商:Taylor & Francis Group
年代:2000
数据来源: Taylor
|
4. |
Development and Experimental Validationof a Flmd/Structure-Interaction Finite Element Modelof a Vacuum-Driven Cell Culture Mechanostimulus System |
|
Computer Methods in Biomechanics and Biomedical Engineering,
Volume 3,
Issue 1,
2000,
Page 65-78
THOMAS D. BROWN,
MICHAEL BOTTLANG,
DOUGLAS R. PEDERSEN,
ALBERT J. BANES,
Preview
|
PDF (809KB)
|
|
摘要:
A new fluid/structure-interaction finite element formulation is reported, by means of which reactive fluid stresses can be determined for what is currently the most widely used laboratory apparatus (; the Flexercell Strain Unit ) for delivering controlled in vitro mechanical stimuli to cultured cells. The apparatus functions by means of cyclic vacuum application to the undersurface of a membrane-like circular rubber substrate. When operated in Us original embodiment ( i.e., without axial constraint to substrate motion), the pulsatile vacuum causes appreciable pulsatile excursions ( often several millimeters) of the substrate. The mechanical stimuli experienced by cells attached atop the substrate include not only substrate distention, but also potentially confounding reactive fluid stresses due to coupled motions of the overlying liquid culture nutrient medium. Since it is impractical to directly measure reactive fluid stress in such environments, a corresponding mathematical model has been developed. The formulation involves transient continuum finite element solutions for the nutrient medium flow field and for the deformation of the substrate, coupled at their mutual interface ( the substrate culture surface) Besides the nonlinearities inherent in the flow field and substrate treatments per se, the numerical problem is complicated by the presence of moving boundaries at the nutrient free surface and at the nutrient/substrate interface, as well as by the need to enforce fluid/structure interaction throughout the duty cycle. Algorithmic considerations appropriate to achieving physically realistic numerical performance are reported, and a confirmatory laboratory validation experiment is described.
ISSN:1025-5842
DOI:10.1080/10255840008915254
出版商:Taylor & Francis Group
年代:2000
数据来源: Taylor
|
|