|
1. |
Thermal stability of synthetic oils in aviation applications |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 275-284
B. Koch,
Preview
|
PDF (402KB)
|
|
摘要:
AbstractThe thermal decomposition of selected synthetic base fluids has been investigated. The effects of temperature and time on the rate and extent of thermal degradation were studied in a modified steel bomb test device. The effects of chain length and branching are important factors in the thermal stability of hydrocarbons and similar fluids. In order to overcome the 350°C limit of thermal stability, other classes of chemical have to be used
ISSN:0265-6582
DOI:10.1002/jsl.3000060402
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
2. |
Development of a meta‐stable semi‐synthetic lubricant for cold rolling of steel |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 285-298
S. Mahanti,
A. K. Bhatta,
R. N. Biswas,
J. Bhatia,
S. N. Singh,
Preview
|
PDF (695KB)
|
|
摘要:
AbstractA semi‐synthetic meta‐stable oil system for cold rolling of steel was developed as a substitute for a mineral oil based ‘stable emulsion’‐type soluble oil. The developed oil system, comprising a ‘coating oil’ for post‐pickling application and a ‘rolling oil’ for the rolling operation, was tested in the laboratory and subsequently subjected to extensive field trials in an integrated steel plant. Use of the developed oil system resulted in 25–50 per cent lower roll loads and 30–50 per cent reduction of inter‐stand tensions compared with the mineral oil‐based ‘stable emulsion’. It was also possible to increase the ‘strip reduction ratio’ and input coil width with the use of the newly‐developed oil. Overall performance of the new semi‐synthetic oil was found to be far superior to that of
ISSN:0265-6582
DOI:10.1002/jsl.3000060403
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
3. |
Rotary‐vane compressors: Some technical aspects of long‐life lubricants |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 299-309
J.‐P. Légeron,
L. Beslin,
Preview
|
PDF (344KB)
|
|
摘要:
AbstractCompressors are used all over the world for various individual applications; the current application concerns their use in the ozone process of water treatment. Technical data on different mineral and synthetic lubricants are given. In particular, a new oil was chosen for investigation. Field testing was undertaken over more than 6000 h on two different locations. Used oil monitoring was conducted by sampling during the experiment; analyses of physical and chemical parameters were made and their kinetics are described. Wear, viscometrics and ozone process interaction are discussed in this study.
ISSN:0265-6582
DOI:10.1002/jsl.3000060404
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
4. |
Lubrication of hydroelectric turbine thrust bearings with a diester‐based synthetic lubricant |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 311-323
R. H. Boehringer,
F. Neff,
Preview
|
PDF (793KB)
|
|
摘要:
AbstractA diester‐based lubricant was found to reduce friction substantially in the thrust bearings of a hydroelectric turbine, compared with a conventional petroleum oil. Bearing temperatures were immediately reduced by 10–11 °C and bearing failures were eliminated. Revenue savings estimated at $10,000,000 per year have been made due to an increase in power production, and the elimination of repair work and downtime co
ISSN:0265-6582
DOI:10.1002/jsl.3000060405
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
5. |
Influence of cutting fluids on surface finish of holes drilled into aluminium 390 |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 325-338
Herman R. Leep,
Preview
|
PDF (683KB)
|
|
摘要:
AbstractThe primary objective of this research was to compare the surface finish resulting when using a semi‐synthetic cutting fluid to that of a premium soluble oil. The secondary objective was to determine the effects of drill diameter, cutting speed, and fluid concentration on surface finish.The surface measurements were made on the walls of 6.350 and 9.525 mm lind holes drilled 25.4 mm into aluminium 390. Each cutting fluid was introduced using a flood application. Additional factors in the experimental design for each cutting fluid included two levels of cutting speed and two levels of fluid concentration.Variations in drill diameter, cutting speed, and the interaction between these factors were significant with respect to surface finish for both the semi‐synthetic fluid and the soluble oil. Fluid concentration for the semi‐synthetic fluid also had a significant effect on the surface finish. The surface finish produced while using the semi‐synthetic fluid was approximately the same as that with the solu
ISSN:0265-6582
DOI:10.1002/jsl.3000060406
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
6. |
Abstracts |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 339-339
Preview
|
PDF (38KB)
|
|
ISSN:0265-6582
DOI:10.1002/jsl.3000060407
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
7. |
Literature |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 340-346
Preview
|
PDF (319KB)
|
|
ISSN:0265-6582
DOI:10.1002/jsl.3000060408
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
8. |
Meetings calendar |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 347-353
Preview
|
PDF (347KB)
|
|
摘要:
AbstractA detailed listing of future meetings of interest to the lubricants community. For further information, readers should apply to the address given. News on forthcoming lubricants conferences is welcome for inclusion in this section.
ISSN:0265-6582
DOI:10.1002/jsl.3000060409
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
9. |
Directory |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page 354-358
Preview
|
PDF (264KB)
|
|
摘要:
AbstractJSLincludes this section on the activities, products and services offered by its subscribers, This listing appears each issue, and is updated regularly, to help readers locate those companies of potential use to the synthetic lubricants community. To participate, fill in the form provided at the back of this issue, and send it to the publishers at the address given on the back of the form.
ISSN:0265-6582
DOI:10.1002/jsl.3000060410
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
10. |
Masthead |
|
Journal of Synthetic Lubrication,
Volume 6,
Issue 4,
1990,
Page -
Preview
|
PDF (55KB)
|
|
ISSN:0265-6582
DOI:10.1002/jsl.3000060401
出版商:John Wiley&Sons, Ltd
年代:1990
数据来源: WILEY
|
|